QNAP TS-x51 and TS-X51A feature comparison Though the case sizes and configuration remain the same, the new models have a teal colored strip along the left side of the front panel. The chart below shows a comparison between the original TS-x51 series and the new TS-x51A models. This provides the convenience of direct-attach storage, but without DAS performance. Essentially, you get a USB port that looks, behaves and performs like a Gigabit Ethernet port, but using USB 3.0, not Ethernet. The blurb below snatched from the A series product page provides the gist of the feature. The big innovation the A series brings is what QNAP has dubbed a USB QuickAccess port. Both models use the same Intel N3060 Celeron dual core processor, are also available in a 2 GB versions (TS-251A-2G and TS-451A-2G) and can be upgraded to 8 GB of RAM total. As in the past, we had QNAP send the four-bay TS-451A-4G, which we loaded with only two drives to generate data for the TS-251A. This brings us to the TS-x51A family we’re looking at today. Since then, QNAP followed up with the TS-x51+, based on a 2 GHz quad-core Intel Celeron J1900 processor, which we didn’t review. We reviewed the original TS-x51 series around two years ago. So the above can now be used as a solution how to configure your Mac computer and a QNAP NAS using ethernet.QNAP’s TS-x51 series is a mainstay of its Home and SOHO product family. Maybe like me unplug the Ethernet cable and plug in again - after about 2 minutes it magically worked. Then you need some patience - because Qfinder keeps for a while reporting the old wrong IP adresss. So I configured ETH2 to 192.168.2.101 and savedĪbove the IP settings for ETH1 and ETH2 I set the Standart Gateway to EtH2 (cause theres the cable plugged in) now and press save button. I then go to Configuration and enter a static IPĭNS Server: set to automatically fetch from networkĪnd as Qfinder didn't change the "found NAS" IP after I reconfigured it - I found out that in Settings I changed ETH1 only - but Qfinder reports ETH2. Now Qfinder "finds" my NAS and reports it with IP Address 169.254.100.100 Can the cable reach the Huawei router instead of the Mac? There may be other, better ways to design your home network. Features that need that won't work, but you should be able to use the web interface and the file shares from your Mac.Īlso note that this is advice for finishing what you have already started - no more, no less. Note that in this setup the NAS won't have any internet access. Now you are done and should be able to log in at. At that point, you should be able to run QFinder and discover the NAS, but the IP address of the NAS will still be generally invalid - go ahead and use the QFinder to set it to 192.168.2.11. You should enter the same 255.255.255.0 for the subnet mask, but leave the default gateway (and generally any other settings) blank. You could choose 192.168.2.10 for the Mac and configure it. In this example, you could choose 192.168.2.x and make up two addresses. Let's say you also get 192.168.1.x and the same subnet mask, which are common (but not to be taken for granted) router defaults. Their examples show what it would look like with an IP address of 192.168.1.112 and the subnet mask of 255.255.255.0. Start with #3, to determine what not to choose: you can use the instructions here for finding your internal address. The addresses need to 1)follow some rules about the address ranges you should use 2)be on the same subnet 3)not conflict with the address range used by your wifi router that the Mac is connecting to. Sounds like you attempted something along those lines, but didn't pick suitable values. This can work, but you need to configure both the Mac's ethernet interface and the NAS with static IP addresses. The network consists of the Mac and the NAS, both of which are trying to be DHCP clients, without an available DHCP server. The problem is that right now, as you have described things, there is no DHCP service on your ethernet network. I played around an set it to 111.111.111.111 as IP address.įunny thing is now from time to time Qfinder sees my NAS with IP 169.254.100.100 - and I can change its Network configuration via Qfinder.īut sometimes I cant connect because when I enter my password I get the error "receiving answer from server failed" I set the Mac system preferences for networking to use DHCP with manual address on the Ethernet port.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |